Offer Yamaha Distribution Power Amps

Yamaha Distribution Power Amps - XH200

	Model: XH200 Yamaha Distribution Power Amps This distribution amplifier delivers 200 watts + 200 watts and is compatible with 100V and 70V lines
	Features Specifications

Compact, Lightweight 200W + 200W Distribution Power Amp for Installed Systems The XH200 is the ideal distribution power amp for use with numerous high-impedance speakers in theatre, hall, and conference facility installations. In addition to being remarkably lightweight, the XH200 is a compact 2U size that will fit comfortably in just about any installation. This combination of high power output and small size has been realized through the use of an advanced switching power supply. The XH200 also features a monitor/remote connector that allows remote status monitoring and control from an external device

Features

Two 200W Channels In a 2U Power Amp
Monitor/Remote and Other Important Functions

Euroblock Input/Output Connectors, and Barrier Strip Output Connectors

General Specifications
Output power 40 Hz-20 kHz THD+N= 0.1 %	70 V, RL=25ohms	MIN	200 W x 2
	100 V, RL=50ohms		200 W x 2
Power consumption	Standby		5 W
	Idle		40 W
	1/8 (4ohms/Pink noise)		400 W
Total harmonic distortion	40 Hz-20 kHz, Half Power	MAX	0.1%
Intermodulation distortion	60 Hz:7 kHz, 4:1, Half Power	MAX	0.1%
Frequency response	Po=1 W, HPF=40 Hz, 80 Hz-20 kHz	MAX	0 dB
		TYP	0 dB
		MIN	-0.5 dB
S/N ratio	(DIN AUDIO)	MIN	103 dB
Channel separation	Half Power, 1 kHz, Att. max, input 600ohmsshunt	MIN	Half Power, 1 kHz, Att. max, input 600ohmsshunt
Residual noise	Att. min,(DIN AUDIO)	MAX	-65 dBu
InputSensitivity	Att. max	TYP	+4 dBu
Voltage gain	Att. max	TYP	38 dB (100 V), 35 dB (70 V)
Maximum input voltage		MIN	+22 dBu
Actual load impedance		TYP	20 kohms(balanced), 10 kohms(unbalanced)
control	Front panel		POWER switch (push on/push off) attenuator (31 position) x 2
	Rear panel		OUTPUTVOLTAGE switch (100 V/70 V) x 1 HPF switch (40 Hz/80 Hz 12 dB/oct) x 2
Connector	INPUT		Euroblock connector (balanced) /ch
	SPEAKERS		Barrier strip/ch
	MONITOR/REMOTE		Dsub 15P x 1
indicator	POWER/STANDBY		x 1 (Green/Orange)
	SIGNAL		x 2 (Green)
	CLIP/LIMIT		x 2 (Red)
	PROTECT/MUTE		x 1 (Red)
Speaker protection			POWER switch on/off mute DC-fault: output relay off/ restored automatically. Clip limiting : THD≥0.5%
Amplifier protection			Thermal: Cuts the output (when heatsink temp.≥90 degrees celsius); operation restored automatically. VI limiter (RL?16ohms): Limits the output.
Power requirements			120V/60Hz 230V/50Hz 240V/50Hz
Idle power consumption			40W
Power consumption			250W
Cooling			Variable-speed fan x 1
Dimensions (W x H x D)			480 x 88 x 412 mm
Weight			9.8 kg
0 dBu=0.775 Vrms, Half Power=1/2 Output Power (3 dB below rated power)