|
The XM series multi-channel power amplifiers are ideal for theater, hall, and conference room installations. The lineup includes 80W x 4 and 180W x 4 models,
meeting the needs of a wide variety of installed systems. The XM amplifiers are a compact 2U size and surprisingly lightweight, making them easy to handle and
install. Switching power supplies deliver high output power while minimizing the unit's physical size. The XM series has monitor/remote jacks that allow external
devices to be connected for status monitoring or control from a remote location.
|
• Four High-Power Channels In One Amplifier
Both of these amps provide four independent channels of power amplification in convenient, manageable units (XM4180 = 180W, XM4080 = 80W). The XM4180 and
XM4080 are suitable for a wide range of installed systems.
• Stereo, Parallel, or Bridged Operation
Three operational modes can be selected as required: the stereo mode provides four independent channels of amplification, the parallel mode allows two mono
sources to drive dual amplifiers each, and in the bridged mode two channels operate as a single high-power mono amp, effectively giving you two higher
powered mono amps in one unit. The operating mode can be easily switched from the rear panel.
• Versatile Input/Output Connectivity
Two types of input jacks are provided; balanced XLR types and Euroblock jacks for easy, secure input connection. Output connections are made via five-way
binding posts. A high pass filter with a selectable 20 Hz or 55 Hz roll-off frequency is also provided. Precision attenuators and independent indicators are
provided for each channel, allowing accurate level setup and status monitoring.
• Distribution Drive Capability (XM4180)
The XM4180 is also capable of functioning as a distribution power amp that can drive multiple high-impedance speakers via 70V line output.
• Monitor/Remote Jack
The rear panel provides a Monitor/Remote jack that allows the amp to be monitored and controlled from an external device. |
| 100V models |
XM4180 |
| Output power; 1kHz |
4ohms |
250W x4 |
| 8ohms |
210W x4 |
| 8ohms; Bridge |
500W x2 |
| Output power; 20Hz-20kHz |
4ohms |
230W x4 |
| 8ohms |
180W x4 |
| 8ohms; Bridge |
460W x2 |
| 70V line |
300W x2, Bridge / 16ohms |
| 120V models |
XM4180 |
| Output power; 1kHz |
4ohms |
250W x4 |
| 8ohms |
210W x4 |
| 8ohms; Bridge |
500W x2 |
| Output power; 20Hz-20kHz |
4ohms |
230W x4 |
| 8ohms |
180W x4 |
| 8ohms; Bridge |
460W x2 |
| 70V line |
300W x2, Bridge / 16ohms |
| 230V models |
XM4180 |
| Output power; 1kHz |
4ohms |
250W x4 |
| 8ohms |
210W x4 |
| 8ohms; Bridge |
500W x2 |
| Output power; 20Hz-20kHz |
4ohms |
230W x4 |
| 8ohms |
180W x4 |
| 8ohms; Bridge |
460W x2 |
| 70V line |
300W x2, Bridge / 16ohms |
| 240V models |
XM4180 |
| Output power; 1kHz |
4ohms |
250W x4 |
| 8ohms |
210W x4 |
| 8ohms; Bridge |
500W x2 |
| Output power; 20Hz-20kHz |
4ohms |
230W x4 |
| 8ohms |
180W x4 |
| 8ohms; Bridge |
460W x2 |
| 70V line |
300W x2, Bridge / 16ohms |
| General specifications |
XM4180 |
| Total harmonic distortion |
Less than 0.1% (20Hz-20kHz; Halfpower), RL=4ohms |
| Inter modulation distortion |
Less than 0.1% (60Hz:7kHz=4:1; Halfpower) |
| Frequency response |
+0dB, -0.5dB (RL=8ohms, 20Hz - 20kHz) |
| S/N ratio |
103dB |
| Crosstalk |
Less than -60dB |
| Damping factor |
More than 100 |
| Voltage gain |
30dB |
| Input sensitivity |
+4dBu |
| Maximum input voltage |
+22dBu |
| I/O Connectors |
Line input / output ports |
4x XLR-3-31, 4x Euroblock |
| Speaker output ports |
4x 5-way binding post |
| Control ports |
D-sub 15pin |
| Processors |
HPF (20Hz/55Hz/OFF, 12dB/Oct) |
| Protection circuit |
Load protection |
Power switch on/off mute, DC-fault (Output relay off; Restored automatically), Clip limiting (THD ≥ 0.5%) |
| Amplifier protection |
Thermal (Mute the output; heatsink temp ≥ 90°C; return automatically), VI limiter (Limit the output, RL ≤ 2ohms) |
| Power supply protection |
Thermal (Amplifier shuts down automatically; Operation not restored automatically; heatsink temp ≥ 90°C) |
| Amplifier class |
EEEngine |
| Cooling |
Variable-speed fan |
| Power requirements |
Depend on area of purchase; 100V, 120V, 230V or 240V; 50/60Hz |
| Power consumption |
Music source equivalent |
600W |
| Idling |
40W |
| Stand-by |
5W |
| Dimensions |
W |
480mm; 18-7/8in |
| H |
88mm; 3-7/16in (2U) |
| D |
412mm; 16-1/4in |
| Net weight |
10kg; 22.1lbs |
| Accessories |
Owner’s manual, AC power cable, Security cover, 4x 3-pin Euroblock connector |
|
|
|
