CCU-D50P

Features ( PAL Version )

• Interfaces with Sony DXC-D50PL Series digital cameras(*1) via its associated CA-D50 Camera Adaptor.

• The output of the CA-D50 Camera Adaptor is transferred to the CCU-D50P Camera Control Unit as a component digital SDI(*2) signal via a Sony CCZ-A 26-pin cable up to 75 m long.

• The distance between the CA-D50 Camera Adaptor and CCU-D50P Camera Control Unit can be extended to a maximum 200 m by providing a separate low loss coaxial video cable to carry the SDI signal between the two units.

• Switchable to accept analog component/VBS signals from DVCAM camcorders,

• DSR-570WSP/390P, equipped with a 26-pin interface. Maximum cable length from the camcorder to the CCU-D50P in analog transfer mode is 300 m(*3).

•  Outputs analog composite and one of the following: component digital SDI, analog component (Y/R-Y/B-Y or RGB), or S-video(*4).

•  Flexible intercom connectivity allows the interfacing of 2-wire or 4-wire systems. *Green tally indication included for use in mid to large-scale camera operations. *The RCP-TX7 or the RM-M7G can be connected to the CCU-D50P.

(*1) Some DXC-D50P Series of digital cameras may require software upgrade to use the CCU-D50P. (*2) Embedded audio is not supported.

(*3) The distance between the camcorder and the CCU-D50P may vary depending on system requirements. (*4) Available output signals depend on.
 

Applicable Models for CCU-D50P

DSR-390PK1 DVCAM Camcorder

DSR-390PK2 DVCAM Camcorder

DSR-390PL DVCAM Camcorder

DXC-D50PH 3-chip CCD Portable Color Camera

DXC-D50PK 3-chip CCD Portable Color Camera

DXC-D50PL 3-chip CCD Portable Color Camera

DXC-D50WSPL 3-chip CCD Portable Color Camera

RM-M7E Remote Control Panel

Supplied Accessories

AC power cord (1)

Rack mount adaptor (2)

Rack mount screw (4)

Tally indication segment (1)

Operation manual (1)

Optional Accessories

RCP-TX7 Remote Control Panel

RM-M7G Remote Control Unit

CCZ-A Cables 26-pin/26-pin Cable

Specifications

General

Power requirements: AC 200/240 V, 50/60 Hz

Power consumption: Approx. 0.8 A

Operating temperature: 5°C to 40°C (41°F to 104°F)

Storage temperature: -20°C to 55°C (-4°F to 131°F)

Dimensions: 424 (W)  88 (H)  283 (D) mm  / (16 3/4  3 1/2  11 1/4 inches)

Mass: 6.3 kg (13 lb 14 oz)

Input/Output connectors

VBS output: BNC (2) 1.0 Vp-p, 75 .

R/G/B output: BNC (1) 0.7 Vp-p, 75 .

Y/R-Y/B-Y output: BNC (1), Y: 1.0 Vp-p, 75 ., R-Y/B-Y: 0.525 Vp-p, 75 .

Y/C output: BNC (1) Y: 1.0 Vp-p, 75 ., C: 0.3 Vp-p, 75 .

SYNC output: BNC (1), 0.3 Vp-p, 75 .

SDI output: BNC (2), 270 Mb/s, 0.8 Vp-p, 75 .

S-Video output: DIN 4-pin (1), Y: 1.0 Vp-p, 75 .,

C: 0.3 Vp-p, 75 .

Monitor output: BNC (1) VBS:1.0Vp-p, 75.

Mic output: XLR 3-pin (1), 600.

Genlock input: BNC (1), loop-through, VBS or BBS,

1.0 Vp-p, 75.

SDI input: BNC (1), 270 Mb/s, 0.8 Vp-p, 75 .

Return Video input: BNC (1), loop-through, 1.0 Vp-p, 75 .

Prompter Video input: BNC (1), loop-through, 1.0 Vp-p, 75 .

Camera: Sony Z-type 26-pin (1)

Intercom/Tally: D-sub 15-pin, 4W/2W selectable, R/G Tally,

contact

Remote: 10-pin (1)

Control functions

Iris (auto/manual), White Balance

(auto/manual/preset),

Black balance (auto/manual/preset), Gain

select (low/mid/high),

R/B White, R/B Black, Master Black,

Sub-carrier Phase, Horizontal Phase,

Output Mode (color bar/camera), Knee

Point (auto/manual), Detail Level,

Master Gamma, Tally/Intercom, Shutter

Speed, Clear scan, ATW